How to Eliminate Common Production Defects of Clay Fired Bricks and Blocks？

Stable thermal and pressure control is the core of high-quality fired brick production in a tunnel kiln. The automatic control system coordinates multiple functional units to govern airflow, oxygen supply, heat recovery and pressure sealing. Understanding how the exhaust fan, hot air extraction fan, kiln car bottom sealing system and hatch dampers interact helps brick manufacturers stabilize firing curves, cut coal consumption and reduce defective underfired bricks.

The exhaust fan is the master airflow driver of the whole kiln system. It draws flue gas sequentially through the cooling zone, soaking zone, firing zone and low-temperature preheating zone via hatch dampers. Airflow moves opposite to the travel direction of green bricks. Two core purposes are served: delivering oxygen to sustain coal combustion in the firing zone, and sending waste hot flue gas to dry green bricks in the drying chamber.

In the low-temperature preheating section, flue gas preheats green bricks until embedded coal ignites. Combustion raises the temperature to the peak firing point. The air volume must match coal feed to maintain proper oxygen level, ensuring 70%–80% of internal coal burns out in the firing zone. If airflow is insufficient, incomplete combustion generates limited heat, leading to an uneven fire line. Excessive airflow carries excessive heat away, dragging down the overall kiln temperature.

Working independently, the hot air extraction fan extracts sensible heat purely from the cooling zone for brick drying, with no oxygen supply for combustion. Any rise in hot extraction volume pulls heat out faster, lowering temperature across cooling, soaking, firing and preheating zones. Reduced extraction retains more heat inside the kiln. Its airflow direction opposes the exhaust fan, which means hot extraction competes for airflow capacity and can pull down kiln temperature. A high hot extraction rate near the firing zone will halt fire propagation and trigger overfiring in the brick stack center. When cooling blower supply stays fixed, over-extraction can create oxygen shortage for combustion.

Pressure sealing relies on the kiln car bottom channel and sand seal system. Wind baffles and coarse sand troughs separate the under-car air duct from the kiln interior. Once pressures balance between the car bottom and kiln chamber, cross air leakage stops. Upward leakage causes underburnt bricks; downward leakage burns kiln car metal structures. The safe temperature range for the kiln car bottom is 70℃ to 100℃.

Mung-bean-sized coarse sand is preferred for sand seals. Fine sand gets blown away easily, while coarse sand is continuously distributed by kiln car baffles to seal the trough tightly, preventing air bypass.

Pressure balance is maintained by balance fans paired with pressure transmitters. Traditional tunnel kilns running under full negative pressure use suction-type balance fans. Discharge-end cooled tunnel kilns feature negative pressure in preheating zones and positive pressure in cooling zones, requiring one suction fan and one blower fan for dual-section balance. Variable frequency drives adjust fan flow based on real-time pressure feedback from two monitoring points, synchronizing car-bottom pressure with kiln pressure. Mechanical balance gates can create negative pressure but lack automatic adjustment capacity and cannot operate in positive-pressure sections.

Low-temperature preheating hatch dampers control kiln positions No.1 to No.10 up to 560℃. The collective opening of these dampers controls total system airflow, while different opening combinations tune local temperature distribution.

The maximum lift of each hatch damper equals its radius. The required damper quantity is calculated by taking the square of the ratio between main duct diameter and single damper diameter. For a 1.2 m main flue and 0.4 m damper, the ratio equals 3, requiring 9 fully open dampers, or 18 dampers (9 pairs) running at half opening. This configuration minimizes pressure loss across dampers.

When fans are controlled by VFDs, operators should fully open damper passages to avoid wasting fan pressure on throttling resistance. Damper profile and opening directly decide fire speed and production capacity. Standard bricks, perforated bricks and hollow bricks require separate damper schedules. Settings also change for wet green bricks and pre-dried green bricks. If fan minimum speed still brings overly fast fire movement, damper pattern and opening should be revised to stabilize drying air pressure and flow.

The thermal principle of hatch dampers is simple: more hot flue gas passing through a damper position means longer heat exchange and higher local brick temperature.

Tunnel kilns are widely used in the brick firing sector to produce fired brick and various kiln products. The kiln car frame and sand sealing plate, manufactured from castings or steel sheets, work under continuous high-temperature atmosphere. These components are exposed directly to hot gas inside the kiln. If they cannot withstand thermal expansion deformation and thermal oxidation corrosion, the thermal tightness of the kiln car will deteriorate rapidly after long operating hours.

Defective kiln cars cause frames to lose support for groove bricks. Kiln car shaking during travel destabilizes the whole firing process. The bricks suffer abnormal deformation and cold cracks, lowering finished product quality. Once such problems emerge during kiln running, immediate on-site repair is impossible. Production has to continue until kiln shutdown. In extreme cases, groove bricks lose balance and the kiln car frame collapses, damaging the main kiln body, kiln bed, wheels and rail system.

When thermal tightness of sand sealing plates fails, high-temperature gas escapes through gaps between the kiln wall and kiln car side panels into the undercarriage. This creates uneven temperature distribution inside the tunnel kiln, leading to inconsistent firing and cold cracking of bricks. Kiln wheels and rails also suffer accelerated wear. These faults cannot be repaired online, so production must keep running until kiln stop.

To solve these typical problems in brick firing production, we carried out multiple structural improvements on the kiln car system. Our target is to enhance refractory performance, durability, and thermal tightness, with durability as the core optimization objective. These upgrades have achieved satisfying application results.

Detailed Improvement Solutions

1. Kiln Car Main Body Structure Optimization

The kiln car assembly consists of metal frame, groove bricks, supporting protrusions on the frame, sand sealing plates covering the lower side of groove bricks, and thermal insulation layers laid inside groove bricks. The metal frame functions as the load-bearing skeleton.

Removable sand sealing plates are vertically fixed on the end face of the kiln car frame. Mounting bases on both lower ends of the frame support vertical installation. The sand sealing plates run from front to rear on both sides of the kiln car. Their top edge covers the bottom part of groove bricks and frame end face.

Protrusions parallel to the travelling direction of the kiln car are arranged slightly inward above the frame. Groove bricks are placed between these protrusions and fixed sand sealing plates. Groove bricks connected along the moving direction form two side walls of the kiln car, preventing hot gas from leaking backward to the undercarriage area.

Vertically mounted sand sealing plates support the bottom outer wall of groove bricks and cover frame end surfaces. This structure separates the metal frame from direct contact with high-temperature gas, preventing thermal expansion deformation and thermal oxidation corrosion. A refractory insulation layer on top of the frame forms part of the kiln bed. Together with side wall structures, it blocks hot gas from penetrating downwards.

2. Assembled Refractory Panel Type Sand Sealing Plate

The sand sealing plate is assembled by two or more refractory panels, vertically mounted and easy to disassemble. It covers the bottom of groove bricks and both end faces of the frame. This setup protects the metal frame from direct high-temperature impact. When individual refractory panels get damaged and thermal tightness drops, the tunnel kiln can keep operating. Damaged refractory panels can be replaced conveniently during maintenance.

3. Gap Sealing with Fiber Felt Materials

Fiber felt sealing materials are filled in all connecting gaps: sand sealing plate and groove brick joints, mounting gaps between sand sealing plates and frame, groove brick and frame contact areas, groove brick and protrusion gaps, protrusion and insulation layer joints, insulation materials and frame gaps, and seams of multi-piece assembled sand sealing plates. This sealing design further stops hot gas leakage into the undercarriage.

4. Embedded Groove Brick Anti-slip Construction

Groove bricks adopt embedded structures matching the frame protrusions. Embedded connection locks groove bricks firmly to avoid sliding. The detachable vertical sand sealing plates cover both ends of the frame. The metal frame will not touch high-temperature gas directly. Even partial refractory panels are damaged, kiln operation can continue and component replacement is convenient.

5. Refractory Ceramic Coating for Metal-based Sand Sealing Plates

For metal-made sand sealing plates, refractory ceramic coating can be applied on the surface. Thin metal sheets with refractory ceramic coating can deliver the same anti-deformation and anti-thermal oxidation performance.

The production of fired wall materials is a systematic project composed of interconnected process stages. Every production segment works like a wooden plank for a water bucket. The maximum water capacity of the bucket is limited by the shortest plank rather than the longest one. Similarly, the profitability of a brick production line is determined by its weakest process link, which we call the short board principle for brick plants.

Many brick factory owners focus only on nominal production capacity at the planning stage. They immediately ask for daily output of 500,000 or 800,000 pieces, annual capacity of 150 million or 200 million fired brick. However, few calculate the actual total material turnover volume on site. The real daily turnover may reach 5 million to 8 million pieces, far higher than the nominal brick output.

Raw Material Stockyard

Some plants use local gangue and shale without extra storage yards. If raw materials are transported from elsewhere, you need multiple stockyards capable of holding 500,000 pieces of brick raw materials.

Raw Material Processing

The daily raw material processing capacity must exceed the target daily brick output, and equipment operation time is only 8–10 hours. Operators need to select crushers, roller screens, single-stage or two-stage crushing solutions according to raw material hardness and moisture content. You also need to confirm belt conveyor width, running speed, magnetic separator configuration and easy maintenance design. Even with large crushers and powerful motors, replacing hammerheads for half a day or one day will directly cut your output. Many small brick plants rely on loaders and manual lifting for heavy screen plates, lacking overhead cranes. Frequent turnover of maintenance staff becomes a typical production short board.

Aging Storage and Fine Material Silo

Aging silos play a vital role in brick manufacturing. The recommended storage capacity supports 3 times daily output with 72-hour aging time. It can maintain raw material supply even when crushing equipment is shut down for 2 days. For hard or sandy raw materials, waterproof design prevents uneven moisture (dry top, wet bottom). Installing soil kneaders after aging and mixing helps stabilize raw material performance.

Extrusion and Forming

The whole extrusion forming system includes feeding, mixing, intensive stirring, extrusion, cutting and brick stacking. The vacuum extruder and brick stacking machine performance varies greatly with raw material properties and product positioning. One set of equipment may work well in one region but fail in another. A typical case: many brick plants in Lanzhou copied production experience from central and eastern China. They obtained fine green bricks, but suffered slow drying, slow firing, high reject rate and cracking. Their actual firing output was much lower than expected, creating a serious short board.

Drying Chamber

Multiple configurations are available for tunnel kiln: direct drying & direct firing, one drying + one firing, one drying + two firing, two drying + one firing, etc. The best option depends on raw materials, finished products and local climate. Direct drying and direct firing suits plastic shale or coal gangue for solid bricks. But for raw materials with high drying sensitivity, direct drying & direct firing will become an irreversible short board.

Special climate also brings challenges. In Kuitun, Xinjiang, extremely dry air causes green body cracking right after cutting. The solution includes lowering the height of workshop and green brick shelter, using curtains to raise ambient humidity and adopting 1.5x brick stacking layout. The track and kiln car quantity must also increase by 1.5 times.

Drying heat sources include flue gas drying, waste heat drying and combined flue gas & waste heat drying. If raw materials contain high sulfur, flue gas drying will cause secondary pollution and increase environmental costs. Low-sulfur raw materials benefit most from combined drying, which saves power and fuel.

Moisture exhaust methods include centralized exhaust, decentralized exhaust, sectional centralized exhaust, positive pressure and negative pressure exhaust. Pure centralized moisture exhaust is inefficient with high power consumption and excessive oxygen. The optimal scheme combines decentralized and centralized exhaust, dominated by positive pressure and assisted by negative pressure. Many rotary tunnel kiln projects have defective drying chamber design; some moisture exhaust fans consume 3–4 times power of the tunnel kiln itself.

Firing Process

Kiln performance, product quality and coal consumption are basically determined in kiln design and construction stage. There are masonry tunnel kilns, combined tunnel kilns, upper air duct kilns, lower air duct kilns and rotary tunnel kilns. Rotary tunnel kilns hold about 300 standard bricks per cubic meter, while traditional tunnel kilns can hold 400–500 pieces. Traditional tunnel kilns are limited by structural defects: bricks move while kiln stays static, leading to cross-section temperature difference and kiln car burning. Overcoming this long-existing structural weakness requires technological innovation.

Firing Technician Capability

Many operators mistakenly regard kiln firing as simply watching flame. A qualified kiln operator must be a kiln adjuster. He needs to master kiln structure, air flow, waste heat, fan volume, temperature, heat value, brick stacking plan, kiln car and drying chamber parameters.

There is a well-known rule: 70% performance comes from brick stacking, 30% from firing; 70% work under the kiln, 30% above the kiln. Excellent technicians analyze raw material test reports and heat distribution. Never feed coal at kiln car joints in high-temperature zones, or open fire holes here, which will damage kiln cars severely. Kiln car burning also relates to kiln car insulation and air balance in trenches.

Loading Lane

One real case: a 3.7m width kiln with 4 drying + 3 firing zones only has one loading lane with semi-automatic packing machine. No extra space can be reserved for additional lanes. The factory could never run full 4-drying-3-firing mode after 5–6 years of operation; maximum operation is only two firing zones. Insufficient loading lanes block finished brick delivery, which is a hard-to-fix planning short board. The number of loading stations, packing stations and holding stations must be calculated in advance according to target output.

Finished Product Yard

Finished storage yard is ignored by many brick plants. Limited yard space plus large kiln capacity leads to production reduction in rainy seasons or off-seasons. Hollow bricks require larger storage yards. Lack of yard space becomes a tough short board for hollow brick manufacturing.

Raw Material & Environmental Compliance

Many factories skip raw material lab testing before construction. Raw materials with 4%–5% sulfur without alternative sources will become an insurmountable short board under environmental regulations. Multiple lab tests are required before investment. High calcium content causes deliquescence; high potassium oxide and magnesium oxide trigger efflorescence and white salt bloom on brick surface.

Desulfurization Tower

Many brick plants rebuilt desulfurization towers because suppliers lack knowledge of kiln structure and fluid mechanics. Poorly designed desulfurization equipment increases fan load, hinders moisture exhaust and reduces output. Horizontal plus vertical flue desulfurization & dust removal performs better than single vertical type. The air inlet of desulfurization tower set slightly above kiln surface saves power and fits fluid mechanics rules.

Environmental Protection and Kiln Upgrade

Natural gas firing delivers clean production with low sulfur, nitrogen oxide and dust pollution. Factory owners need to evaluate whether existing kilns can be modified for natural gas combustion without full reconstruction. New kiln projects should consider fuel options in early design.

Conclusion

The full-cycle capacity formula for tunnel kiln production:

1. Raw material stock: multiple times of daily output
2. Raw material processing capacity ≥1.5× daily output
3. Aging capacity: 2–3× daily output
4. Extruding within 8–12h to reach 1× daily output
5. Green brick storage:1.5–2× daily output
6. Empty kiln car ≥0.5× daily output
7. Drying capacity:1× daily output
8. Firing capacity:1× daily output
9. Finished brick transport lane ≥0.75× daily output
10. Loading station ≥0.3× daily output
11. Finished yard: multiple times daily output

The whole system maintains turnover of dozens of times nominal daily output. A plant targeting 500,000 bricks per day may need 5 million bricks in total turnover.

Fired wall material manufacturing is a complete system covering raw material preparation, processing, extrusion, stacking, green brick drying, firing and finished product handling. Profitability of your brick factory is determined by the weakest link.

In modern brick manufacturing plants, environmental standards and energy costs have become two major challenges for factory owners. One of the key factors affecting kiln energy consumption and emission performance is the oxygen content in tunnel kiln exhaust gas.

Many brick factories try to reduce exhaust oxygen levels by simply adjusting fans, air pressure, or damper openings. However, the real solution requires a systematic understanding of tunnel kiln air management.

By eliminating unnecessary air, reducing air leakage, and optimizing combustion air supply, brick factories can achieve better fuel efficiency, more stable firing quality, and lower environmental emissions.

This article explains how the three principles of correct air usage, reducing useless air, and optimizing reasonable airflow can help improve modern fired brick production processes.

1. Why Exhaust Oxygen Content Matters in Brick Manufacturing

During the fired brick making process, combustion requires a certain amount of oxygen to ensure complete fuel burning. However, excessive air entering the kiln does not improve combustion efficiency. Instead, it increases the amount of exhaust gas and raises the oxygen content measured in the kiln exhaust.

High oxygen content in exhaust gas usually indicates:

•   -Excessive air entering the tunnel kiln
•   -Heat loss caused by unnecessary airflow
•   -Higher exhaust temperature
•   -Increased energy consumption
•   -Difficulty meeting environmental monitoring requirements

For this reason, controlling oxygen content in kiln exhaust gas has become an important indicator for improving energy-saving brick production.

2. Eliminate Incorrect Air: The First Step of Tunnel Kiln Optimization

Clay brick manufacturing remains one of the most fundamental segments of the global building material industry. Many brick manufacturers face a common challenge: limited workshop space when upgrading or building new clay brick production lines. Traditional brick making equipment, especially horizontal brick cutters, requires large floor areas, which restricts factory expansion and raises workshop construction costs.

For small-to-medium brick factories and newly built compact production workshops, space utilization directly affects overall project investment and long-term operational efficiency. Choosing space-saving core machinery becomes a key decision point in the whole brick plant design.

The Automatic Vertical Brick Splitter Cutter is a core piece of equipment specially developed to solve the space shortage problem in brick workshops. It is designed for precise vertical cutting of extruded mud columns and separates continuous mud extrusions into individual brick green bodies.

Different from conventional horizontal brick cutters, this vertical cutting structure greatly reduces the occupied floor space. It works synchronously with brick extruders in the production line, perfectly fitting compact brick factory layouts.

Core Benefits

✅ Space Optimization: Vertical cutting design saves workshop floor area, ideal for factories with limited land.

✅ Stable Matching with Extruders: Connects directly after extruders to process continuous clay mud columns.

✅ Flexible Integration: Easy to install into both new brick production lines and old production renovation projects.

FAQ

Q1: What is the function of vertical brick splitter cutter in clay brick production line?

A: It performs precise vertical cutting on extruded mud columns and cuts the continuous clay extrusion into standard-sized brick green bodies.

Q2: Can vertical brick cutting machine be used for old brick factory renovation?

A: Yes. Its compact footprint makes it a good option for upgrading existing production workshops with limited available space.

Q3: What is brick green body in brick manufacturing?

A: Brick green body is the unfired raw brick before entering the drying chamber and tunnel kiln for sintering.

Q4: What equipment works together with vertical brick splitter cutter?

A: It is normally matched with clay brick extruders, and forms a complete mud extrusion and cutting unit.